Supplier of Zenith Trans-oceanic parts

11/10/2007 9:29:21 PMAndy Rolfe

Good evening everyone;
Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave bands. Thanks again; Andy

11/10/2007 9:39:35 PMEddie

:Good evening everyone;
:Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave
bands. Thanks again; Andy

Andy - I retrieved that Philco "Conecentric" chassis which has the tuning knob/shaft parts I think you wanted (37-4 ir 37-7). I couldn't seem to reach you by e-mail. ALSO - if you find a source for those red suction cups, I need some.
Eddie

11/11/2007 8:14:40 AMAndy Rolfe

::Good evening everyone;
::Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave
:bands. Thanks again; Andy
:
:Andy - I retrieved that Philco "Conecentric" chassis which has the tuning knob/shaft parts I think you wanted (37-4 ir 37-7). I couldn't seem to reach you by e-mail. ALSO - if you find a source for those red suction cups, I need some.
:Eddie

Eddie; Yes I am still interested in the tuning knob/ shaft parts from our earlier posts for the Philco 38-7. Let me know what the price is. You can email me at asrolfe@rogers.com
Thanks; Andy

11/24/2007 11:10:32 AMEddie

:::Good evening everyone;
:::Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave
::bands. Thanks again; Andy
::
::Andy - I retrieved that Philco "Conecentric" chassis which has the tuning knob/shaft parts I think you wanted (37-4 ir 37-7). I couldn't seem to reach you by e-mail. ALSO - if you find a source for those red suction cups, I need some.
::Eddie
:
:
:Eddie; Yes I am still interested in the tuning knob/ shaft parts from our earlier posts for the Philco 38-7. Let me know what the price is. You can email me at asrolfe@rogers.com
:Thanks; Andy

Hi Andy,
Have you been checking your e-mail? You wanted one or the other of us to set a price (with shipping) on the Philco Cone-centric knob and shaft set - and I have also been asking if you might need anything else off of it while I have the chassis out.
Have fun,
Eddie

11/24/2007 11:55:42 AMTonyJ

I am also in need of the tuning and vernier knob as well as the knob screw to secure them to the tuning shaft for a 38-7 that I will be receiving in the mail shortly if you may have another set. Also have a 38-7 that is missing 2 tube shields and bases if you have them available also. My email is tony_senior @ yahoo.com Thanks!

::::Good evening everyone;
::::Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave
:::bands. Thanks again; Andy
:::
:::Andy - I retrieved that Philco "Conecentric" chassis which has the tuning knob/shaft parts I think you wanted (37-4 ir 37-7). I couldn't seem to reach you by e-mail. ALSO - if you find a source for those red suction cups, I need some.
:::Eddie
::
::
::Eddie; Yes I am still interested in the tuning knob/ shaft parts from our earlier posts for the Philco 38-7. Let me know what the price is. You can email me at asrolfe@rogers.com
::Thanks; Andy
:
:Hi Andy,
:Have you been checking your e-mail? You wanted one or the other of us to set a price (with shipping) on the Philco Cone-centric knob and shaft set - and I have also been asking if you might need anything else off of it while I have the chassis out.
:Have fun,
:Eddie

11/25/2007 6:06:54 AMAndy Rolfe

::::Good evening everyone;
::::Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave
:::bands. Thanks again; Andy
:::
:::Andy - I retrieved that Philco "Conecentric" chassis which has the tuning knob/shaft parts I think you wanted (37-4 ir 37-7). I couldn't seem to reach you by e-mail. ALSO - if you find a source for those red suction cups, I need some.
:::Eddie

Hi Eddie: I don't know what's happening with the e-mail you are sending because I'm not receiving it!!! Yes I'm still in need of the tuning knob/shaft pieces from the philco 38-7 set. Why don't you post your e-mail address and I can try to contact you this way. Would you trade me these parts for 2 red suction cups plus I'll throw in $10 ????

Thanks; Andy
::
::
::Eddie; Yes I am still interested in the tuning knob/ shaft parts from our earlier posts for the Philco 38-7. Let me know what the price is. You can email me at asrolfe@rogers.com
::Thanks; Andy
:
:Hi Andy,
:Have you been checking your e-mail? You wanted one or the other of us to set a price (with shipping) on the Philco Cone-centric knob and shaft set - and I have also been asking if you might need anything else off of it while I have the chassis out.
:Have fun,
:Eddie

11/26/2007 8:02:44 AMEddie

:::::Good evening everyone;
:::::Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave
::::bands. Thanks again; Andy
::::
::::Andy - I retrieved that Philco "Conecentric" chassis which has the tuning knob/shaft parts I think you wanted (37-4 ir 37-7). I couldn't seem to reach you by e-mail. ALSO - if you find a source for those red suction cups, I need some.
::::Eddie
:
:
:Hi Eddie: I don't know what's happening with the e-mail you are sending because I'm not receiving it!!! Yes I'm still in need of the tuning knob/shaft pieces from the philco 38-7 set. Why don't you post your e-mail address and I can try to contact you this way. Would you trade me these parts for 2 red suction cups plus I'll throw in $10 ????
:
:Thanks; Andy
:::
:::
:::Eddie; Yes I am still interested in the tuning knob/ shaft parts from our earlier posts for the Philco 38-7. Let me know what the price is. You can email me at asrolfe@rogers.com
:::Thanks; Andy
::
::Hi Andy,
::Have you been checking your e-mail? You wanted one or the other of us to set a price (with shipping) on the Philco Cone-centric knob and shaft set - and I have also been asking if you might need anything else off of it while I have the chassis out.
::Have fun,
::Eddie

11/26/2007 8:09:38 AMEddie

:::::Good evening everyone;
:::::Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave
::::bands. Thanks again; Andy
::::
::::Andy - I retrieved that Philco "Conecentric" chassis which has the tuning knob/shaft parts I think you wanted (37-4 ir 37-7). I couldn't seem to reach you by e-mail. ALSO - if you find a source for those red suction cups, I need some.
::::Eddie
:
:
:Hi Eddie: I don't know what's happening with the e-mail you are sending because I'm not receiving it!!! Yes I'm still in need of the tuning knob/shaft pieces from the philco 38-7 set. Why don't you post your e-mail address and I can try to contact you this way. Would you trade me these parts for 2 red suction cups plus I'll throw in $10 ????
:
:Thanks; Andy
:::
:::
:::Eddie; Yes I am still interested in the tuning knob/ shaft parts from our earlier posts for the Philco 38-7. Let me know what the price is. You can email me at asrolfe@rogers.com
:::Thanks; Andy
::
::Hi Andy,
::Have you been checking your e-mail? You wanted one or the other of us to set a price (with shipping) on the Philco Cone-centric knob and shaft set - and I have also been asking if you might need anything else off of it while I have the chassis out.
::Have fun,
::Eddie

Hi Andy,

That sounds about right - but wait - I just looked into my needs - what would it do if I needed 6 of those red Zenith suction cups?
Also - a couple of things made me wonder if you're British, so let me ask if you have a red Mullard EF39?
- - - you can try e-mail, but there must be something awefully wrong with it between our addresses.
Thank You,
Eddie

11/10/2007 10:07:04 PMRadiodoc

Andy,

You might check out:

http://www.radioera.com/zenithparts.asp

They have parted out some Zenith TOs and have some of the parts listed there.

Radiodoc
**********

:Good evening everyone;
:Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave bands. Thanks again; Andy

11/11/2007 8:21:32 AMAndy Rolfe

Radiodoc; Thanks for info. I got exactly what I wanted. Andy

:Andy,
:
:You might check out:
:
:http://www.radioera.com/zenithparts.asp
:
:They have parted out some Zenith TOs and have some of the parts listed there.
:
:Radiodoc
:**********
:
:
::Good evening everyone;
::Does anyone know where I might find a brass swing catch used to keep the front panel of an 8G005YT in the locked position? The swing part has broken off. I'm also looking for 2 of the red rubber suction cups. If you know of a supplier I would appreciate your help. I purchased this set at the Kalamazoo,Michigan swap meet for $90 and it is in nice condition and plays great even on some shortwave bands. Thanks again; Andy